GL324 DATASHEET PDF

GL Quad Operational Amplifier Components datasheet pdf data sheet FREE from Datasheet (data sheet) search for integrated circuits (ic). GL Datasheet, GL PDF, GL Data sheet, GL manual, GL pdf, GL, datenblatt, Electronics GL, alldatasheet, free, datasheet, Datasheets, . GL Datasheet, GL PDF, Quad Operational Amplifier.

Author: Tukasa Nir
Country: Turks & Caicos Islands
Language: English (Spanish)
Genre: Spiritual
Published (Last): 9 March 2005
Pages: 204
PDF File Size: 13.11 Mb
ePub File Size: 14.90 Mb
ISBN: 283-1-97592-336-6
Downloads: 21623
Price: Free* [*Free Regsitration Required]
Uploader: Zoloramar

What you need to do is simulate this circuit — Schematic created using CircuitLab As you showed it, the measurements and signals, having no connection to any reference point common to the op amp, are never going to make sense. Probably pins were loose I didnt notice in the first way.

Sign up or log in Sign up using Google. Post Your Answer Discard By clicking “Post Your Answer”, you acknowledge that you have read our updated terms of serviceprivacy policy and cookie policyand that your continued use of the website is subject to these policies.

WhatRoughBeast 49k dxtasheet 28 ThePhoton I used another IC now on the breadboard. I use 12VDC as Vcc. If you applied -9V from a single rail supply, you’ve probably fried it. What could be wrong? If I apply 9V as input there is no output.

GL Datasheet – Operational Amplifier from

Please edit your schematic to show what you actually connected. And above is a photo from my setup. Email Required, but never shown. By using our site, you acknowledge that you have read and understand our Cookie PolicyPrivacy Policyand our Terms of Service. I use the following data sheet: I use the following data sheet:.

  KAPUSTIN PASTORALE PDF

I can roughly see that, but have you probed each pin with the multimeter to check it is at the expected voltage – e.

(Datasheet) GL pdf – DataSheet 4 U .com DataShee Quad Operational Amplifier (1-page)

Two browns are GND and Vcc for the opamp. Your problem is that your signal voltages and meters are not connected to power supplies, but are completely floating. You are a good learner!

But I think I figured out the problem.

For many of us, we can understand your circuit much more quickly by looking at your schematic than by reading your words. Andy aka k 10 The opamp was defect definitely. I dont think thats problem here.

If I apply reverse voltage with the 9V battery, I see minus reading from the voltmeter. Sign up using Email and Password. By clicking “Post Your Answer”, you acknowledge that you have read our updated terms of serviceprivacy policy and cookie policyand that your continued use of the website is subject to these policies. All grounds all connected. So you are saying the opamp is broken? I’m having trouble when I’m trying to make a voltage-follower from GL opamp.

  GAIL CARRIGER HEARTLESS PDF

As you showed it, the measurements and signals, having no connection to any reference point common to the op amp, are never going to make sense. What you need to do is.

Can’t tell entirely from the picture but it ratasheet wired up ok unless there are loose connections. Home Questions Tags Users Unanswered. It makes sense what you say.

GL324 Datasheet

I checked many times. It’s been more years than I can remember since using breadboard but shouldn’t the op-amp sit over the trough that runs horizontally through the middle: Thats the only photo remained. I think you are right since in my second try with another lm I inserted it in the middle and it worked. Post as dattasheet guest Name. Have you probed the voltages on each pin to make sure they are correct? I double checked my wiring and it matched the circuit schematics and datasheet.

I’d also try a different amplifier there are 4 in the IC, so try one of the other 3. TomCarpenter Is the schematics right?

Sign up using Facebook. Trouble with a voltage follower Ask Question. I tried with another another brand it worked. And the opamp gets very hot.

Back to top